My new beer brewing stand is getting so close I can almost taste the home brew.

All of the hard plumbing of the gas lines has been completed and tested. The gas valve and pilot light works as expected. After I tightened the pilot light compression fitting the brewing stand seems leak free!

I have completed the based for the top tier and secured it in place.

So… What’s left?  I need to complete the design for the easy dump top tier.  I am developing something a bit different than the tipsy dump. If all goes well, it will function a bit smoother.

I need to mount the pump and also intend on adding a longer propane “in” hose.

The propane banjo burner and propane jet burner have been plumbed. The main vertical tube is assembled using 1/2″ steel black pipe.  The Banjo burner has a 1/4″ ball valve assembled in-line.

This system is designed for 10 (or less) psi propane to enter the main black pipe assembly. From there, the propane will flow to the Banjo Burner and the Jet Burner. The Jet Burner has a 1/2 psi regulator prior to propane entering the gas valve. (Since the gas valve functions at 1/2 psi) The gas valve is part of the automation system.

It’s getting really close to being completed.

One of the main components of my mash process is the Tri Clover RIMS tube which I purchased from Brewers Hardware. The RIMS tube contains an electric water heater element and temperature sensor.  Liquid wort will be circulated through the RIMS tube. The BCS 460 will turn the heating element on and off based on input from the temperature sensor.

I have now completed the mounting of the RIMS Tube on my new brewing stand. The RIMS tube is mounted vertically using two electrical pipe clamps. Removal of RIMS Tube for cleaning only requires turning two wing nuts.

The water heater element will be mounted at the bottom of the RIMS Tube.

I also completed the brackets for the Hot Liquor Tank gas valve. The burner and gas valve have their own individual brackets to support their weight. The gas valve is protected by a heat and liquid drip shield.

Stay tuned for the results of the gas line and component plumbing.

Like most brewers, I am interested on always finding a better way to do things. I own a Banjo burner along with several jet burners and have been tossing around my opinion of what really is a better burner. I have yet come to any conclussion. I have, however, reached an opinion on where the High Pressure Banjo burner might work better.

This test was done with the interest of boil in mind. I wanted to know how quick I could reach a boil after mash out.  I ran the test using a low pressure jet burner at .5 psi and a high pressure Banjo burner at 10 psi. Both propane burners were ran fully open and had their own propane source.

Two very similar stainless converted kegs (kettles) containing 6.5 gallons each were used.  I started this test at 166 on both kettles. Altitude for my testing location was around 980 feet.  I monitored the temperature of both kettles using a laptop, BCS460 , and two temperature probes.

When I made this video, I broke it into several  different segmants. Excuse the redundancy in advance!

Without spoiling the results from the video,  it is my opinion that the high pressure Banjo burner would make a great burner for your boil kettle or possibly your hot liquor tank. It is a little hot to be controlling your mash tun and takes adjusting if you want to reduce the heat.  After around twelve and a half minutes, the Banjo burner had the Jet burner by around seventeen degrees.

I enjoy the gadgets of brewing as much as the brewing itself. In fact, I often find myself making changes to a brewing sculpture for my own entertainment. Does it make the beer taste any better? Most likely not. But… It sure is fun.

I decided that I wanted to change one of my Jet Burners over to a Cast Iron Banjo Burner. I faced two separate challenges with this installation. One was mounting, and the other was plumbing. The jet burner was previously mounted and supported with black gas pipe. The jet burner did not have the weight of the Banjo Burner and connected to 1/2 inch black gas pipe without additional supports. Not trivial at all. The Banjo Burner, however,  is connected to the gas supply by way of a brass orifice. The Brass orifice will not support the weight of the burner so brackets needed to be built.

The Banjo Burner is approximately 10 inches around and 15 inches in length at its longest point. The Banjo Burner comes with four mounting holes on the side of the burner. I created a custom offset bracket using 3/4 inch wide by 1/8 inch thick steel. I completed alignment, clamping, and welded the brackets in place. It fits quite nicely in the space that used to be occupied by the jet burner!

Once in place, it was time for the plumping. I utilized the gas ball valve that was already installed on my Brutus Ten. I didn’t want a long BBQ with extra slop connecting the burner to the gas ball valve so I visited my local Propane Dealer for parts. One of the employees created a customer fit hose to run from the ball valve to the Banjo Burner. This hose really made the project look great.

All the parts were connected and it was time for a test burn! It fired right up and I couldn’t be happier. The Banjo Burner is sooooo much quieter and seems to burn hotter. I can’t wait to compare the results. Stay Tuned!